• ttbc Bosnian: zaustaviti (protok nečega, npr. krvi, suza, i sl.), inf
• ttbc Bahasa: setia

Usage notes

The spelling staunch is more commonly used for the adjective. In contrast, stanch is more commonly used as the spelling of the verb.

A lock is a device for raising and lowering boats between stretches of water of different levels on river and canal waterways. The distinguishing feature of a lock is a fixed chamber whose water level can be varied; whereas in a caisson lock, a boat lift, or on a canal inclined plane, it is the chamber itself (usually then called a caisson) that rises and falls.

Locks are used to make a river more easily navigable, or to allow a canal to take a reasonably direct line across country that is not level.

The term airlock was coined for a similar device used to allow persons to pass to and from a location in which a particular atmosphere is maintained, such as underwater, in space, or in a clean room.

Use of locks in river navigations

A lock is required when a stretch of river is made navigable by bypassing an obstruction such as a rapid, dam, or mill weir — because of the change in river level across the obstacle.

In large scale river navigation improvements, weirs and locks are used together. A weir will increase the depth of a shallow stretch, and the required lock will either be built in a gap in the weir, or at the downstream end of an artificial cut which bypasses the weir and perhaps a shallow stretch of river below it. A river improved by these means is often called a Waterway or River Navigation (see example Calder and Hebble Navigation).

The lowest lock on a navigable river separates the tidal and non-tidal stretches. Sometimes a river is made entirely non-tidal by constructing a sea lock directly into the estuary.

In more advanced river navigations, more locks are required.

• Where a longer cut bypasses a circuitous stretch of river, the upstream end of the cut will often be protected by a flood lock.
• The longer the cut, the greater the difference in river level between start and end of the cut, so that a very long cut will need additional locks along its length. At this point, the cut is, in effect, a canal.

Use of locks in canals

Early completely artificial canals, across fairly flat countryside, would get round a small hill or depression by simply detouring (contouring) around it. As engineers became more ambitious in the types of country they felt they could overcome, locks became essential to effect the necessary changes in water level without detours that would be completely uneconomic both in building costs and journey time. Later still, as construction techniques improved, engineers became more willing to barge directly through and across obstacles by constructing long tunnels, cuttings, aqueducts or embankments, or to construct even more technical devices such as inclined planes or boat lifts. However, locks continued to be built to supplement these solutions, and are an essential part of even the most modern navigable waterways.

Basic construction and operation

All locks have three elements:

• A watertight chamber connecting the upper and lower canals, and large enough to enclose one or more boats. The position of the chamber is fixed, but its water level can vary.
• A gate (often a pair of "pointing" half-gates) at either end of the chamber. A gate is opened to allow a boat to enter or leave the chamber; when closed, the gate is watertight.
• A set of lock gear to empty or fill the chamber as required. This is usually a simple valve (traditionally, a flat panel (paddle) lifted by manually winding a rack and pinion mechanism) which allows water to drain into or out of the chamber; larger locks may use pumps.

The principle of operating a lock is simple. For instance, if a boat travelling downstream finds the lock already full of water:

• The entrance gates are opened and the boat sails in.
• The entrance gates are closed.
• A valve is opened, this lowers the boat by draining water from the chamber.
• The exit gates are opened and the boat sails out.

Notes

• If the lock were empty, the boat would have had to wait 5-10 minutes while the lock was filled.
• For a boat travelling upstream, the process is reversed: for instance, the chamber is filled by opening a different valve which allows water to enter the chamber from the upper level.
• The whole operation will usually take between 10 and 20 minutes, depending on the size of the lock, and whether it was originally set "for" the boat.
• Boaters approaching a lock are usually pleased to meet another boat coming towards them, because this boat will have just exited the lock on their level and therefore set the lock in their favour — saving some work and some 5-10 minutes. (This is not true for staircase locks, where it is quicker for boats to go through in convoy.)

Details and terminology

For simplicity, this section describes a basic type of lock, with a pair of gates at each end of the chamber and simple rack and pinion paddles raised manually by means of a detachable windlass operated by the boat's shore crew. This type can be found all over the world, but the terminology here is that used on the British canals. A subsequent section explains common variations.

Rise

The change in water-level effected by the lock. The two deepest locks on the English canal system are Bath deep lock on the Kennet and Avon Canal and Tuel Lane Lock on the Rochdale Canal which both have a rise of nearly 20ft (sources vary as to the exact rises, so it is not possible to guarantee which is the deeper of the two). Both locks are amalgamations of two separate locks, which were combined when the canals were restored to accommodate changes in road crossings. The deepest "as-built" locks in England are considered to be Etruria Top Lock on the Trent and Mersey Canal or Somerton Deep Lock on the Oxford Canal, both of which have a rise of about 14ft. Again, sources vary as to which is the deepest and in any case Etruria has been deepened over the years to accommodate subsidence. A more typical (English) rise would be 7-12 feet (though even shallower ones can be encountered).

Pound

The level stretch of water between two locks (on a river, the corresponding term is commonly reach). The lock allows a boat to move between the pound above it (upper pound) and the pound below it (lower pound).

Chamber

The main feature of a lock. It is a watertight (masonry, brick, steel or concrete)enclosure which can be sealed off from the pounds at either end by means of gates. The chamber may be the same size (plus a little manoeuvring room) as the largest vessel for which the waterway was designed; sometimes larger, to allow more than one such vessel at a time to use the lock. The chamber is said to be "full" when the water level is the same as in the upper pound; and "empty" when the level is the same as in the lower pound. (If the lock has no water in it at all, perhaps for maintenance work, it might also be said to be empty, but a less-confusing term for this is "drained".)

Cill

A narrow horizontal ledge protruding a short way into the chamber from below the upper gates. Allowing the rear of the boat to "hang" on the cill is the main danger one is warned to guard against when descending a lock, and the position of the forward edge of the cill is usually marked on the lock side by a white line. The edge of the cill is usually curved, protruding less in the centre than at the edges.

Gates

The watertight doors which seal off the chamber from the upper and lower pounds. Each end of the chamber is equipped with a gate, or pair of half-gates, made of oak or elm (or now sometimes steel). When closed, a pair meet at an angle like a chevron pointing upstream (this arrangement is often called mitre gates) and a very small difference in water-level squeezes the closed gates securely together. This reduces any leaks from between them and prevents their being opened until water levels have equalised. If the chamber is not completely full, the top gate is secure; and if the chamber is not completely empty, the bottom gate is secure (in normal operation, therefore, the chamber cannot be open at both ends). A lower gate is taller than an upper gate, because the upper gate only has to be tall enough to close off the upper pound, while the lower gate has to be able to seal off a full chamber. The upper gate is as tall as the canal is deep, plus a little more for the balance beam, winding mechanism, etc; the lower gate's height equals the upper gate plus the lock's rise.

Balance beam

A long arm projecting from the landward side of the gate over the towpath. As well as providing leverage to open and close the heavy gate, the beam also balances the (non-floating) weight of the gate in its socket, and so allows the gate to swing more freely.

Paddle

The simple valves by which the lock chamber is filled or emptied. A paddle is a sliding wooden (or nowadays plastic) panel which when "lifted" (slid up) out of the way allows water to either enter the chamber from the upper pound or flow out to the lower pound. A gate paddle simply covers a hole in the lower part of a gate; a more sophisticated ground paddle blocks an underground culvert. There can be up to 8 paddles (two gate paddles and two ground paddles at both upper and lower ends of the chamber) but there will often be fewer. For a long period since the 1970s it has been British Waterways policy not to provide gate paddles in replacement top gates if two ground paddles exist. The reason for this has been safety, since it is possible for an ascending boat to be swamped by the water from a carelessly lifted gate paddle. However, this makes the locks slower to operate and has been blamed in some places for causing congestion. Since the late 1990s there has been some relaxation of this policy, but it seems to be by no means universal.

Winding gear / paddle gear

The mechanism which allows paddles to be lifted (opened) or lowered (closed). Typically, a square-section stub emerges from the housing of the winding gear. This is the axle of a sprocket ("pinion") which engages with a toothed bar ("rack") attached by rodding to the top of the paddle. A member of the boat's shore crew engages the square socket of their windlass (see below) onto the end of the axle and turns the windlass perhaps a dozen times. This rotates the pinion and lifts the paddle. A pawl engages with the rack to prevent the paddle from dropping inadvertently while being raised, and to keep it raised when the windlass is removed, so that the operator can attend to other paddles (it is considered discourteous and wasteful of water to leave a paddle open after a boat has left the lock). To lower a paddle the pawl must be disengaged and the paddle wound down with the windlass. Dropping paddles by knocking the pawl off can cause damage to the mechanism – the paddle gear is typically made of cast iron and can shatter or crack when dropped from a height. In areas where water-wastage due to vandalism is a problem, for example the Birmingham Canal Navigations), paddle mechanisms are commonly fitted with vandal-proof locks (nowadays called "water conservation devices", which the authorities believe sounds nicer) which require the boater to employ a key called a "handcuff key" before the paddle can be lifted.

Hydraulic paddle gear

During the 1980s British Waterways began to introduce a hydraulic system for operating paddles, especially those on bottom gates, which are the heaviest to operate. A metal cylinder about a foot in diameter was mounted on the balance beam and contained a small oil-operated hydraulic pump. A spindle protruded from the front face and was operated by a windlass in the usual way, the energy being transferred to the actual paddle by small bore pipes. The system was widely installed and on some canals it became very common. There turned out to be two serious drawbacks. It was much more expensive to install and maintain than traditional gear and went wrong more frequently, especially once the vandals learned to cut the pipes. Even worse, it had a safety defect, in that the paddle once in the raised position could not be dropped in an emergency, but had to be wound down, taking a good deal longer. These factors led to the abandonment of the policy in the late 1990s, but examples of it survive all over the system, as it is usually not removed until the gates need replacing, which happens about every twenty years.

Windlass ("lock key")

A windlass (also known as a 'lock handle', 'iron' or simply 'key') is a detachable crank used for opening lock paddles (the word does not refer to the winding mechanism itself).

The simplest windlass is made from an iron rod of circular section, about half an inch in diameter and two feet long, bent to make an L-shape with legs of slightly different length. The shorter leg is called the handle, and the longer leg is called the arm. Welded to the end of the arm is a square, sometimes tapered, socket of the correct size to fit onto the spindle protruding from lock winding gear.

• Socket: Traditionally, windlasses had a single socket, designed for a particular canal. When undertaking a journey through several canals with different lock-gear spindle sizes it was necessary to carry several different windlasses. A modern windlass usually has two sockets for use on different canals: the smaller is for the British Waterways standard spindle, fitted in the early 1990s almost everywhere, the larger for the gear on the Grand Union Canal north of Napton Junction, which they were unable to convert.
• Handle: The handle is long enough for a two-handed grip and is far enough from the socket to give enough leverage to wind the paddle up or down. There may be a freely-rotating sleeve around the handle to protect the tender hands of a novice boater from the blisters which can be caused by the friction of a rough iron handle turning against soft skin.
• Arm: A "long throw" windlass has a longer arm so that the handle is further from the socket to give a greater leverage on stiffer paddles. If the throw is too long then the user, winding a gate paddle, risks barking their knuckles against the balance beam when the handle is at the lowest point of its arc. A sophisticated modern windlass may have an adjustable-length arm.
• Materials : Early windlasses were individually hand forged from a single piece of wrought iron by a blacksmith. More modern techniques include casting of iron or bronze, drop forging and (the most common technique) welding. Some boatmen had their windlasses 'silvered' (or chrome plated) for increased comfort and to prevent rusting. Windlasses are now only rarely plated, but a popular modern choice of metal is aluminium, whose smooth and rustproof surface has the same advantages of longevity and blister-reduction, and is also very light. One type of these, the Dunton Double, has only a single eye, but by clever tapering it will operate either size of spindle.

"Turning" a lock

This can simply mean emptying a full lock or filling an empty one (We entered the lock, and it only took us five minutes to turn it). It is used more often to refer to a lock being filled or emptied while you are not in it (The lock was turned for us by a boat coming the other way) and particularly when there is no boat in it at all (The lock was set for us, but the crew of the boat coming the other way turned it before we got there).

Variations

Not all locks work exactly as described above, and the terminology changes, too ...

• Single gates on narrow canals (locks approx. 7 feet / 2.1 m wide)
  • A few narrow locks imitate wide locks in having paired gates at both ends (eg Bosley, on the Macclesfield canal)
  • On most English narrow canals however, the upper end of the chamber is closed by a single gate the full width of the lock. This was cheaper to construct and is quicker to operate, as only one gate needs to be opened.
  • Some narrow locks (e.g. on Birmingham Canal Navigations) go even further. They have single gates at the lower end also. This speeds up passage, even though single lower gates are heavy (heavier than a single upper gate, because the lower gate is taller) and the lock has to be longer (a lower gate opens INTO the lock, it has to pass the bow or stern of an enclosed boat, and a single gate has a wider arc than two half-gates).

• Steel Gates. Steel gates and/or balance beams are frequently used nowadays, although all-wooden versions are still fitted where appropriate.
  • Swinging Gates: Even very large steel-gated locks still can use essentially the same swinging gate design as small 250-year-old locks on the English canals. On English canals, steel gates usually have wooden mitre posts as this gives a better seal.
  • Sliding Gates: Some low-head locks use sliding steel gates (see Kiel Canal).
  • Guillotine Gates: Some locks have vertically moving steel gates — these are quite common on river navigations in East Anglia. Sometimes just one of the pairs of swinging gates is replaced by a guillotine: for instance at Salterhebble Locks, where space to swing the balance beams of bottom gates of the lowest lock was restricted by bridge widening. On the River Nene most locks have this arrangement as in time of flood the top mitre gates are chained open and the bottom guillotines lifted so that the lock chamber acts as an overflow sluice.
  • Vertically-Rotating Gates: Gates which, when open, lie flat on the canal bed and which close by lifting (London Flood Barrier).
  • Rotating-Sector Gates. These work very like traditional swinging gates, but each gate is in the form of a sector of a cylinder. They close by rotating out from the lock wall and meeting in the centre of the chamber. English examples are the sea lock on the Ribble Link and the lock at Limehouse Basin which gives access to the River Thames. A dramatically-large one can be seen at the Rotterdam flood defences (huge flood gates).

• Alternate paddle gear
  • Some manually-operated paddles do not require a detachable handle (windlass) because they have their handles ready-attached.
  • On the Leeds and Liverpool Canal there is a variety of different lock gear. Some paddles are raised by turning what is in effect a large horizontal wing nut (butterfly nut) lifting a screw-threaded bar attached to the top of the paddle. Others are operated by lifting a long wooden lever, which operates a wooden plate which seals the culvert. These are known locally as "jack cloughs". Bottom gate paddles are sometimes operated by a horizontal ratchet which also slides a wooden plate sideways, rather than the more common vertical lift. Many of these idiosyncratic paddles have been "modernised" and they are becoming rare.
  • On the Calder and Hebble Navigation, some paddle gear is operated by repeatedly inserting a Calder and Hebble Handspike (length of 4" by 2" hardwood) into a ground-level slotted wheel and pushing down on the handspike to rotate the wheel on its horizontal axis.
  • On some parts of the Montgomery Canal bottom paddles are used in place of side paddles. Rather than passing into the lock through a culvert around the side of the lock gate, the water flows through a culvert in the bottom of the canal. The paddle slides horizontally over the culvert.

• Lock keepers. Some locks are operated (or at least supervised) by professional lock keepers. This is particularly true on commercial waterways, or where locks are large or have complicated features that the average leisure boater may not be able to operate successfully. For instance, although the Thames above Teddington (England) is almost entirely a leisure waterway, the locks are usually staffed. Only recently have boaters been allowed limited access to the hydraulic gear to operate the locks when the keeper is not present.

• Powered operation. On large modern canals, especially VERY large ones such as ship canals, the gates and paddles are too large to be hand operated, and are operated by hydraulic or electrical equipment. Even on smaller canals, some gates and paddles are electrically operated, particularly if the lock is regularly staffed by professional lock keepers. On the River Thames below Oxford all the locks are staffed and powered. Powered locks are usually still filled by gravity, though some very large locks use pumps to speed things up.

• Fish Ladders. The construction of weirs on rivers obstructs the passage of both fish and ships. Some fish such as trout and salmon go upstream to spawn. Measures such as a fish ladder are often taken to counteract this.

Special cases

Lock flights

Loosely, a flight of locks is simply a series of locks in close-enough proximity to be identified as a separate group. For many reasons, a flight of locks is preferable to the same number of locks spread more widely: crews are put ashore and picked up once, rather than multiple times; transition involves a concentrated burst of effort, rather than a continually-interrupted journey; a lock keeper may be stationed to help crews through the flight quickly; and where water is in short supply, a single pump can recycle water to the top of the whole flight. The need for a flight may be purely determined by the lie of the land, but it is possible to purposely group locks into flights by using cuttings or embankments to "postpone" the height change. Examples: Caen Hill locks, Devizes.

A lock flight should not be confused with a lock staircase. In a flight, each lock has its own upper and lower gates, there is a pound (however short) between each pair of locks, and the locks are operated in the conventional way.

Staircase locks

A "stop" lock is a (very) low-rise lock built at the junction of two (rival) canals to prevent water from passing between them.

During the competitive years of the English waterways system, an established canal company would often refuse to allow a connection from a newer, adjacent one. This situation created the Worcester Bar in Birmingham, where goods had to be transshipped between boats on rival canals only feet apart.

Where a junction was built, either because the older canal company saw an advantage in a connection, or where the new company managed to insert a mandatory connection into its Act of Parliament, then the old company would seek to protect (and even enhance) its water supply. Normally, they would specify that, at the junction, the newer canal must be at a higher level than their existing canal. Even though the drop from the newer to the older canal might only be a few inches, the difference in levels still required a lock — called a stop lock, because it was to stop water flowing continuously between the newer canal and the older, lower one. The lock would be under the control of the new company, and the gates would, of course, "point" uphill - towards the newer canal. This would protect the water supply of the newer canal, but would nevertheless "donate" a lockful of water to the older company every time a boat went through. In times of excess water, of course, the lock "bywash" would continuously supply water to the lower canal.

When variable conditions meant that a higher water level in the new canal could not be guaranteed, then the older company would also build a stop lock (under its own control, with gates pointing towards its own canal) which could be closed when the new canal was low. This resulted in a sequential pair of locks, with gates pointing in opposite directions: one example was at Hall Green near Kidsgrove, where the southern terminus of the Macclesfield Canal joined the Hall Green Branch of the earlier Trent and Mersey Canal. The four gate stop lock near Kings Norton Junction, between the Stratford-upon-Avon Canal and the Worcester and Birmingham Canal was replaced in 1914 by a pair of guillotine lock gates which stopped the water flow regardless of which canal was higher. These gates have been permanently open since nationalisation.

Many stop locks were removed or converted to a single gate after nationalisation in 1948. Hall Green stop lock remains, but as a single lock: the extra lock was removed because the lowering of the T&M's summit pound (to improve Harecastle Tunnel's "air draught" — its free height above the water level) meant that the T&M would always be lower than the Macclesfield. The Hall Green Branch is now considered to be an extension of the "Macc", which now meets the T&M at Hardings Wood junction (just short of the Harecastle Tunnel north portal).

It should be noted that the "new canal must be higher" rule is not cast-iron. For instance: the very shallow lock at Autherley Junction, where the 1835 Birmingham and Liverpool canal (now part of the Shropshire Union Canal) met the older (1772) Staffordshire and Worcestershire Canal. The Nicholson guide shows that a boater coming south down the "Shroppie" locks UP before turning N or S onto the to the older S&W - so the Shroppie (the newer canal) gains a small lockful of water each time a boat passes. However, the gain is tiny since the level difference is so small that it is sometimes possible to open both gates at once.

Drop locks

A drop lock allows a short length of canal to be lowered temporarily while a boat passes under an obstruction such as a low bridge. During canal restoration, a drop lock may be mooted where it is impractical or prohibitively expensive to remove or raise a structure that was built after the canal was closed (and where re-routing the canal is not possible).

A drop lock can consist of two conventional lock chambers leading to a sump pound, or a single long chamber incorporating the sump - although the term properly applies only to the second case. As the pounds at either end of the structure are at the same height, the lock can only be emptied either by allowing water to run to waste from the sump to a lower stream or drain, or (less wastefully) by pumping water back up to the canal. Particularly in the two-chamber type, there would be a need for a bypass culvert, to allow water to move along the interrupted pound and so supply locks further down the canal. In the case of the single-chamber type, this can be achieved by keeping the lock full and leaving the gates open whilst not in use. .

Whilst the concept has been suggested in a number of cases, the only example in the world of a drop lock that has actually been constructed is at Dalmuir on the Forth and Clyde Canal in Scotland. This lock, of the single chamber type, was incorporated during the restoration of the canal, to allow the replacement of a swing bridge (on a busy A road) by a fixed bridge, and so answer criticisms that the restoration of the canal would cause frequent interruptions of the heavy road traffic. It can be emptied by pumping - but as this uses a lot of electricity the method used when water supples are adequate is to drain the lock to a nearby burn. A series of pictures showing the operation of the lock can be seen here. A similar arrangement is due to be built as part of the Droitwich Canal restoration.

Flood locks

A flood lock is to prevent a river from flooding a connected waterway. It is typically installed where a canal leaves a river. At normal river levels, the lock gates are left open, and the height of the canal is allowed to rise and fall with the height of the river.

However, if the river floods beyond a safe limit for the canal, then the gates are closed (and an extra lock created) until the river drops again. Since this is a true lock it is possible for boats to leave the canal for the flooded river despite the difference in water levels (though this is not likely to be wise) or (more sensibly) to allow boats caught out on the flood to gain refuge in the canal.

Note that if the canal is simply a navigation cut connecting two stretches of the same river, the flood lock will be at the upstream end of the cut (the downstream end will have a conventional lock).

Flood locks which have been used only as flood gates (see below) are often incapable of reverting to their former purpose without refurbishment. That is, where only outer gates are ever closed (probably because a waterway is not a true commercial one, and therefore there is no financial imperative for a boat to venture out onto a flooded river) inner gates soon suffer from lack of maintenance. A good example is on the Calder and Hebble Navigation, where structures referred to in the boating guides as "Flood Locks" are clearly only capable of being used for flood-prevention, not for "penning" boats to or from the river in flood.

Flood gates

A flood gate or "stop gate" is the cheaper equivalent of a flood lock. Only one set of gates exist, and so when the river is higher than the canal, the gates are closed and navigation ceases. These are quite common in the French inland waterways system. Flood gates may also be used to sub-divide long canal pounds or protect, in case of bank collapse, the surrounding area if this is lower than the water level of the canal. They are commonly found at the ends of long embankments and at aqueducts. These gates are often overlooked because they lack balance beams and are only a little higher than normal canal level.

Bi-directional gates and locks

Where a lock is tidal (i.e. one side of the lock has water whose level varies with the tide) or where a canal meets a river whose level may vary, the water on the tidal or river side (the "downstream" side) may rise above the water on the normal "upper" side. The "upstream" pointing doors will then fail to do their job, and will simply drift open. To prevent water flowing the wrong way through the lock, there will need to be at least one set of gates pointing in the "wrong" direction. If it is desirable that boats can use the lock in these circumstances, then there needs to be a full set of gates pointing towards the tidal or river side. The usual method is to have gates pointing in opposite directions at both ends of the chamber (alternatively, the "paired stop lock" arrangement of two separate sequential locks pointing in opposite directions would work here — but would require an extra chamber). If navigation is not required (or impossible) at one "extreme" (e.g. allow navigation above mid-tide, but just prevent the canal emptying at low tide) then it is only necessary to have one set of bi-directional gates.

Sea locks

A lock connecting a canal or river directly with the estuary (or beach). All sea locks are tidal.

Tidal locks

Loosely, any lock connecting tidal with non-tidal water. This includes a lock between a tidal river and the non-tidal reaches; or between a tidal river and a canal; or a sea lock. However, the term usually refers specifically to a lock whose method of operation is affected by the state of the tide. Examples:

• A canal joining a river whose levels are always lower than the canal. All that is needed is an ordinary lock, with the gates pointing up the canal. The lock is used normally so long as the tide is high enough to float boats through the lower gates. If near low tide the lock becomes unusable, then the gates can be barred (and simply become a "reverse flood gate", holding water in the canal). This arrangement also applies to some sea locks (e.g. Bude Canal).
• A canal joining a river which is normally below it, but which can rise above it (at very high tides, or after heavy rain). One pair of gates can be made bidirectional, ie the inward-pointing gates would be supplemented by a pair pointing out to the river. When the river is higher than the canal, the normal gates would just drift open, but the additional pair of gates can be closed to protect the canal, and prevent navigation to the river. In effect, we have simply added a flood gate.
• As above, but where it is safe to navigate even when the river is higher than the canal. The lock will be fully bidirectional (two pairs of oppositely pointing gates at each end) to allow boats to pass at any normal river levels. At extreme low or high tides unsuitable for navigation, the appropriate sets of gates are barred to prevent passage.

Very large locks

A marine railway is similar to a canal inclined plane in that it moves boats up or down a slope on rails. However, the vessel is carried "dry" (in a carrying frame, or cradle) rather than in a water-filled caisson. The principle is based on the patent slip, used for hauling vessels out of the water for maintenance.

In operation, a boat is navigated into the carrying frame, which has been lowered into the water. The boat is secured to the cradle, possibly by raising slings under the hull using hydraulics, and the cradle is hauled out of the water and up the hill with a cable. At the top of the slope, the cradle is lowered into the upper waterway, and the boat released. As the boat is not floating, Archimedes principle does not apply, so the weight lifted or lowered by the device varies - making counterbalancing (by dead weights or a second boat carriage) more difficult.

In some locations, notably the Big Chute Marine Railway on the Trent-Severn Waterway, in Ontario, Canada, a marine railway was installed as a temporary measure at the planned site of a flight of conventional locks. In this and several other cases, the locks were never built, and the marine railway continued to serve on a permanent basis.

Boat lifts

Here are three types of boat lifts (the last two are currently in operation).

Somerset and Camden

Around 1800 the use of caisson locks was proposed by Robert Weldon for the Somerset Coal Canal in England. In this underwater lift, the chamber was 80 ft long and 60 ft deep and contained a completely enclosed wooden box big enough to take a barge. This box moved up and down in the 60 ft (18.2 m) deep pool of water. Apart from inevitable leakage, the water never left the chamber, and using the lock wasted no water. Instead, the boat entered the box and was sealed in by the door closing behind it, and the box itself was moved up or down through the water. When the box was at the bottom of the chamber, it was under almost 60 feet of water – at a pressure of three atmospheres, in total. One of these "locks" was built and demonstrated to the Prince Regent (later George IV), but it had various engineering problems and the design was not put into use on the Coal Canal. However, in about 1817 the Regents Canal Company built one of these locks at the site of the present-day Camden Lock, north London. Here the motivation was, again, water supply problems. Even though the change in level is much lower than that would have been the case in Somerset, the system was soon replaced by conventional locks. No commercially successful example has ever been built.

Falkirk

The Falkirk Wheel, the world's first rotating boat lift, acts as the centrepiece of the restoration of the Forth and Clyde and Union Canals. The spectacular "Wheel" presents the 21st century's solution to replacing a flight of locks which formerly connected the canals and which were filled-in in 1930. The Falkirk Wheel was the winning design in a competition to design a new lock. Visitors can now take a boat trip on the Wheel and be lifted over 100 feet in a few minutes compared to the time it took when the original lock staircase operated.

Anderton and Strépy-Thieu

The Victorian Anderton Boat Lift, the world's first vertical boat lift, linking the Trent and Mersey Canal and the River Weaver in Cheshire, has recently been restored. The world's highest boat lift of Strépy-Thieu in Belgium raises or lowers 1,350 tonnes boats by 73.15 metres.

A combined system - the Three Gorges Dam

At the Three Gorges Dam on the Yangtze River (Chang Jiang) in China there are two stair-steps of five large ship locks. In addition to this there will be a ship lift (a large elevator) capable of moving a three thousand ton ship vertically in one motion.

Ship sizes named after locks

Locks restrict the maximum size of ship able to pass through, some key canals have given rise to the name of standard ship sizes:

• Panamax
• Seawaymax

References

See also

• Boat lift
  • List of boat lifts
• Canal pound
• Canals of the United Kingdom
• Erie Canal — New York State
• Flash lock
• Fonsérannes locks - at Beziers on the Canal du Midi
• Gongoozler
• Göta Canal - Sweden
• Grand Union Canal
• Kiel Canal This low head single lock uses sliding gates.
• Locks on the Canal du Centre
• Locks on the River Thames
• Murray River — Australia
• Panama Canal
• Peterborough lift lock — Canada (Ontario), an example of a boat lift
• Pound lock
• Rideau Canal — Canada (Ontario)
• Saint Lawrence Seaway — Canada
• Sault Ste. Marie Canal — Sault Ste. Marie, Ontario
• Soo locks — Sault Ste. Marie, Michigan/Ontario
• Trent-Severn Waterway — Canada (Ontario)
• Trollhättan Municipality - lock system from lake to North Sea in Sweden
• Welland Canal — Canada (Ontario)

External links

• Deepest Canal Locks in England

Sabbatarian, airtight, ardent, bigoted, calculable, close, committed, compact, consistent, constant, creedbound, dedicated, dependable, devoted, dogmatic, dustproof, dusttight, evangelical, faithful, faithworthy, fast, firm, firm as Gibraltar, fixed, flinty, fundamentalist, gasproof, gastight, hermetic, hermetically sealed, hidebound, hyperorthodox, immovable, inflexible, infrangible, invincible, liege, lightproof, lighttight, literalist, literalistic, long-lasting, loyal, made of iron, marble-constant, oilproof, oiltight, precisianist, precisianistic, predictable, purist, puristic, puritanical, rainproof, raintight, reliable, resolute, rigid, rugged, sealed, seaworthy, secure, set, settled, shut fast, smokeproof, smoketight, snug, solid, sot, sound, stable, steadfast, steady, steely, stormproof, stormtight, stout, straitlaced, strict, strong, sturdy, substantial, sure, surefire, tested, tight, tough, tried, tried and true, true, true-blue, trusted, trustworthy, trusty, unbending, unbreakable, undeflectable, undeviating, unfailing, unfaltering, unflappable, unflinching, unshaken, unshrinking, unswerving, unwavering, unyielding, water-repellant, waterproof, watertight, well-built, well-constructed, well-founded, well-grounded, well-made, windproof, windtight